Hi all,
Let me introduce myself while presenting one of my successful bondage sessions. The setup, once tuned up, is quite simple, however I got trough 4 versions and 10 sessions until I got it working. The inspiration was the Star Wars scene with Han Solo frozen in a carbonite block, with face and hands visible on the black surface 😇
First, the setup:
Basically, it is a 2 persons, polyurethane mattress, one with no metal strings inside, wrapped in a large transparent PVC bag. the bag was built using PVC sheets sold by meters as table cover, soldered together using a hot glue gun.
The bag does have an opening for the neck - I preferred to leave head outside for safety.There is app. 50cm zipper allowing to widen the neck hole wide enough to sneak in. The zipper was also soldered by hot glue.
Near to the base, there is a small hole to insert the vacuum tube - only the rigid tip of it, and plug the wide vacuum head from inside. The vacuum head, facing the mattress, prevents clogging the tube with the plastic bag.
The open edge of the bag, once the mattress is in, is rolled a bit and fixed using a clothespin each 10cm app. Vacuum will seal it by itself.
Next stage - slipping in, dressed in some nylon body and other nice stuff:
Closing the zipper from inside:
Taking the position, waiting for the vacuum timer. Notice the left hand under a weak patch on the bag, marked by yellow electrician tape - if the test went wrong, it can be broken by fingers to break the vacuum. Otherwise, the PVC sheet is pretty tough and I don't think I could break it without a tool.
1 minute test run: all seems working fine...
So, during the break, I move the hand out of reach of the weak patch. The ride begins!
Even moving a finger is virtually impossible. Really tight bondage! Let do some struggling to enjoy the tight fit 😇
The vacuum first sucks out any air in the bag, then it starts to suck air from the mattress itself, shrinking it to fraction of its width, while sinking the rider deep in.
There are some leaks trough the zipper and around the neck, but vacuum can well outrun these and it prevents the vacuum burning out.
There are 2 timers in series used - one programmed to go off after 20 minutes, second one to go on after 5 minutes for one minute, and then 2 minutes later to go on for 10 minutes....
And, ride is over. Let slip out and dry the bag of the sweet. It is was on hot day, one reason I did not dare to stay in for longer time - I could severely overheat and was unsure the vacuum would burn on time to release me 😁
I hope you enjoyed the ride 😇
Let me introduce myself while presenting one of my successful bondage sessions. The setup, once tuned up, is quite simple, however I got trough 4 versions and 10 sessions until I got it working. The inspiration was the Star Wars scene with Han Solo frozen in a carbonite block, with face and hands visible on the black surface 😇
First, the setup:
Basically, it is a 2 persons, polyurethane mattress, one with no metal strings inside, wrapped in a large transparent PVC bag. the bag was built using PVC sheets sold by meters as table cover, soldered together using a hot glue gun.
The bag does have an opening for the neck - I preferred to leave head outside for safety.There is app. 50cm zipper allowing to widen the neck hole wide enough to sneak in. The zipper was also soldered by hot glue.
Near to the base, there is a small hole to insert the vacuum tube - only the rigid tip of it, and plug the wide vacuum head from inside. The vacuum head, facing the mattress, prevents clogging the tube with the plastic bag.
The open edge of the bag, once the mattress is in, is rolled a bit and fixed using a clothespin each 10cm app. Vacuum will seal it by itself.
Next stage - slipping in, dressed in some nylon body and other nice stuff:
Closing the zipper from inside:
Taking the position, waiting for the vacuum timer. Notice the left hand under a weak patch on the bag, marked by yellow electrician tape - if the test went wrong, it can be broken by fingers to break the vacuum. Otherwise, the PVC sheet is pretty tough and I don't think I could break it without a tool.
1 minute test run: all seems working fine...
So, during the break, I move the hand out of reach of the weak patch. The ride begins!
Even moving a finger is virtually impossible. Really tight bondage! Let do some struggling to enjoy the tight fit 😇
The vacuum first sucks out any air in the bag, then it starts to suck air from the mattress itself, shrinking it to fraction of its width, while sinking the rider deep in.
There are some leaks trough the zipper and around the neck, but vacuum can well outrun these and it prevents the vacuum burning out.
There are 2 timers in series used - one programmed to go off after 20 minutes, second one to go on after 5 minutes for one minute, and then 2 minutes later to go on for 10 minutes....
And, ride is over. Let slip out and dry the bag of the sweet. It is was on hot day, one reason I did not dare to stay in for longer time - I could severely overheat and was unsure the vacuum would burn on time to release me 😁
I hope you enjoyed the ride 😇
