Ice time-locks

[Like Ra]

grr I so need one of these! The commercial one doesn't come close in justifying the $200 price tag...

Absolutely. $200 is a rip off.

Such a pity that I don't have the skills to construct something as simple as this!! lol I wish someone can make me one and I'll pay for it 😋

Probably you never tried 😉 It's not that difficult. To simplify things further you can replace the ring part with a rope loop.

about your http://www.likera.com/sb/time/ice-padlock2.php
Would the chain get tangled instead the bottle? That would suck wouldn't it...

That would indeed. It did not when I tested it. On the other hand, see this post. So, if you are completely immobile (and can't shake the bottle with your bound hands) I would advise to use a less risky method or to find a bottle with a wider bottleneck.

I have tried Ra's design, but used a light chain instead of nylon cord. The chain can and does get stuck. When it does, it is a big problem. Fortunately, I was able to unscrew one pipe cap. But, if I had not been able to reach the ice lock, I would have been in serious trouble.

I haven't had any trouble with nylon cord, not doubled. Currently, I'm using 3mm braided nylon. Example: http://www.rei.com/product/784296 .

[Like Ra]

I have tried Ra's design, but used a light chain instead of nylon cord.

Binaryfreedom was talking about a different design: http://www.likera.com/sb/time/ice-padlock2.php

The chain can and does get stuck. When it does, it is a big problem.

And you mean this one, right? - http://www.likera.com/sb/time/ice-padlock3.php
I would not use chain here.

I haven't had any trouble with nylon cord, not doubled. Currently, I'm using 3mm braided nylon. Example: http://www.rei.com/product/784296 .

Yes, please DO NOT double it. Or it MAY get entangled. Actually, the bigger the hole and the shorter the cord - the less chance it gets stuck. You can test it by twisting the aeady inserted cord and trying to pull it out. I could NOT make NOT doubled cord stuck whatever I tried. Of course, if you make a knot on the other side ... 😉

BTW, I have another design in my mind. It will be a bit bigger but on the same time even more reliable.

Seen as i finally ordered a pile of stuff off of ebay and will be making something like one of these.

http://www.likera.com/sb/time/ice-padlock3.php

I'm going to try something a little smaller though. I'll let you know how i get on and add pictures too.

[Like Ra]

Yes, please! That would be interesting!

This a sweet lock, Ra!

I couldn't find the 40mm parts here, so I used 1.25 inch iron pipe. You can get pre-threaded pipe nipples (yes, that's what plumbers call stubby pieces of pipe), end-caps and ther rest of the parts in any local hardware store. Used a few layers of electrical tape for insulation. Otherwise, the design, parts and construction were the same.

The iron pipe must conduct heat a little faster than plastic. Mine thawed out in about 2.5 hours.

Thanks for the grand idea!

Next time I have a cup of tea from a van, i will try puting water in the cup with lid on and freeze it. I know those cups keep the tea hot for ages so should keep ice as ice a long time too cheers, Paul

A long overdue update to this thread...

ice lock

Looks like this could be a much more affordable pre-built ice-lock for those who's DIY is not up to making one.

MJ

[Like Ra]

a much more affordable pre-built ice-lock

35 quid is indeed much more affordable than what they had before. Add an insulation layer (neoprene? rubber foam?) and you'll get ~3-4 hours. The lock is a bit too long, though - 19cm.