Hi All
Im new here and new to Latex
Im looking for Mens Latex Pants with the Inflatable Butt Plug for Enemas - It also
has a Sheath - I saw one on Ebay but its too large
I've been thinking about going out for a walk in high heels, but there is a problem. Where I live, there is no place I can go out without (the posibility of) being seen.
I wear size 41, but I feel comfortable with women's size 40. So my first option was to buy myself some mountain boots size 43. Inside i can hide a women's wedges size 39 without anyone seeing I'm wearing high heels. The problem is that the narrow heel started to cut through the sole of the boots. Not a viable solution for more than a few meters walk.
First lets talk about the ice lock, it's basically the same as described on this very site
Just some pvc bits in 32mm from the hardware store, all glued together. First I used Tec7 but that failed after a while, I patched it up with a hot glue gun and that seems to withstand the freeze/thaw cycles better.
The preparation is simple, put the anchor rope trough the lid:
fill with water, screw the lid in place and put in the freezer. An hour in the freezer gives only 15 minutes or so and a week lock, for full fun at least 4 hours is required.
In this picture you see a steel ring. This ring is used as an anchor point to a rope harness I tie on my upper chest, the ring is then as high as possible between my shoulder blades. It's important that this ring is wide enough for the anchor from the ice lock to pass through (or it must be put there when assembling the ice lock and frozen together) but the container can't.
I do it that way instead of using the ring on the other side of the ice lock to shorten the distance between the anchor point and the rope ratchet. The shorter it is the tighter the bondage will be.
Then the rope ratchet. It's just one from Gamma, it can hold 150 pounds according to the specs but I can lift way more than that and it hasn't slipped once. I made a loop in the rope and tied the end to the carabiner, once it's in the tube it will be out of reach.
Then there is a simple wrist loop, you need to experiment a bit to see what works for you. By pulling the rope from the ratchet tight it will cinch the wrist loop and lift your hands higher up your back.
The ratchet goes into the pvc tube, I have put a screw trough it to hook the carabiner up. This keeps everything in place and prevents you from sliding the tube away from the knot and ratchet release lever.
Detailed look. Don't mind the extra holes, they are a leftover from my experiments of getting it right. I wanted to use a padlock first to lock the ratchet to the tube but that didn't work to well. It could work with a more fitting one, just try it. I went with this solution, I need two wrenches to make the bolts tight so there is no chance of getting them off with just my fingers.
The ratchet in place
side view
As you can see there is no room for desperate fingers to undo the knot or reach the release on the ratchet.
This is the way the ratchet must be attached to the ice lock. Pay very much attention to not attach it to the harness ring because this cancels out the ice release. I did that once and luckily the rest of the ropework was a bit to experimental or that would have been a whole different scenario.
Only 16 cm, that's good for some pretty tight bondage. Note that by using the other ring on the ice lock this distance increases a lot. On top of that I once managed to pull the ice lock apart when I was using it in a hogtie, using the extra ring not only reduces the distance lost but it's also a lot stronger.
This is how far my research and development got me 😊 I'm thinking about getting a special made to measure box 3D-printed that will fit the ratchet better and will only have just enough room for the carabiner and the ropes. That should reduce the distance even further and be less bulky (and more aesthetically pleasing).
It works really well for hands behind the back, lifted up high but also for hogties.
I have not been very active on the forum but I have been recording some sessions and trying out new things. A small selection of some recent and some older material I can share with you is in this clip. There are many edits, cuts and effects applied, there is no music as I ran out of time (leaving on holiday for a week tomorrow) and it's all very rough but I was hoping to get some feedback. Tell me what you like and what not, I want to improve.
I'm trying to come up with a logo or branding for myself, you can see it in the beginning and very end of the clip.
As always, if you see anything you like let me know, I might edit a longer clip from the footage I have or I will record some more. Same for requests, just ask and I'll see what I can do. I should be able to get on the internet from time to time while away but when I'm back I'll have some time to record more stuff.
I'm looking forward to your feedback and questions. Enjoy!
As suggested by Likera last week, I decided to try a new kind of DIY vacbed. This time, I wrap a soft mattress and a hard bed base in the same bag, giving a good comfort and a great immobilization ! So here are some pictures of the way it is done:
Inserting a pillow for comfort...
[attachment=21745]
The vacuum cleaner with the "broom" end is inserted between the soft mattress and the hard base, so the suction is well done everywhere...
[attachment=21746]
Of course, a handle to turn on...
[attachment=21747]
So it gives something like this:
[attachment=21748]
So how is it when being inside ??? Look at this before / after pictures !
I'm putting this here as I can't think of anywhere else!!!
Well After much thought and peer pressure... today I tried the 'cycle with a plug in'... lasted about 5.5miles/9km before it had to come out. The friction on the perrinium was getting uncomfortable and as I was only 1/2 way I didn't want to push it.
I used the ass anchor expando plug as this has the smallest outside portion of my plugs.
Went to fish it out in a dark patch along side a lake only to be passed by a jogger within a few seconds, thankfully he thought I was giving way to him (bit narrow at that point)
Now the only problem was that the excercise and a now relaxed butt that was obviously not as clean as I thought (it was a last minute rushed decision ) meant that there was an additional reason for the cycle gear to go into the washing machine.
And the whole 'shut the bathroom door' thing didn't work as my 2 year old decided he wanted a shower too... the dog vigorously sniffing at the pile of stinky cycle clothes...
I'm collecting ideas on how to make posting easier and more interesting. I can't promise that anything from the suggestions will be implemented (e.g. by myself), but it is possible that someone has already written a plugin or subsystem with the requested capability. There is a Rule 34 adaptation for programming:
o- If something exists, there is an app for that
o- All programs have already been written
And Rule 35:
o- If something exists, but there is no app, it will be written.
This is my idea for a Vacbed ice lock! It works with the expanding force of freezing water. Water has the feature to expand 8-10% when it freezes. I think it may be possible to use this feature, to squeeze a piece of silikone tubing, which is inside a metal pipe.
The vollume of a pipe with 50mm diameter and 80mm hight, wich is filled with Water, should be able to Squeeze a 12mm Diameter tubing.
Here is a drawing for better understanding.
The only problem that could happen, is that the Silicone-tubing is sticking together because of the pressure of the ice or maybe some leaking.
I will try to built a prototype in the next fiew weeks. Then i will see.
If this would work it sould be a realy good emergency release. What do you think.
