+- Like Ra's Naughty Forum (https://www.likera.com/forum/mybb)
+-- Forum: Self-Bondage (https://www.likera.com/forum/mybb/Forum-Self-Bondage)
+--- Forum: Completed Self-Bondage Sessions (https://www.likera.com/forum/mybb/Forum-Completed-Self-Bondage-Sessions)
+---- Forum: Peeklemeekle's Self-Bondage Adventures (https://www.likera.com/forum/mybb/Forum-Peeklemeekle-s-Self-Bondage-Adventures)
+---- Thread: I recently got my first LATEX vacbed (/Thread-I-recently-got-my-first-LATEX-vacbed)
Pages:
1
2
I recently got my first LATEX vacbed - Peeklemeekle - 15 Jan 2024
As you may have seen from my previous posts here, I've done numerous setups and variations for self bondage in cheap, self-made plastic vacbeds.
I finally upgraded to the ultimate and truest form of vacbeds: Latex - And it has not disappointed. I've done a few sessions in it and the tightness level as which it holds you in place very much exceeds that of plastic. It's just so tight and awesome!
I decided not to get a PVC frame and stick with my foam mattress as a frame-alternative, and it's a lovely feeling. Ironically, even though a vacbed really isn't actually a bed, with this setup, it actually is a bed, because it uses a foam mattress. It just so happens there's also some latex ready to hold you firmly in place to it. Although I still don't think you'll be doing any sleeping in this bed 😋
I'm still flying solo as I don't have a partner to help me, but I'm aware of the potential hazards and dangers since I'm no longer using plastic that I can just rip. But I have a well-thought-out setup and choose to accept the risks.
Here are a couple short videos 😊
pose 1 squirm.mp4 (Size: 7.9 MB )
pose 2 squirm.mp4 (Size: 20.93 MB )
😉
RE: I recently got my first LATEX vacbed - unicast - 15 Jan 2024
May I ask how you did manage to left it?
RE: I recently got my first LATEX vacbed - Peeklemeekle - 15 Jan 2024
(15 Jan 2024, 09:36 )unicast Wrote: May I ask how you did manage to left it?
Uhhh, did you make a typo or something? I'm not understanding what you're asking
RE: I recently got my first LATEX vacbed - Like Ra - 15 Jan 2024
I understand the question as "How did you manage to get out?"
RE: I recently got my first LATEX vacbed - Peeklemeekle - 15 Jan 2024
(15 Jan 2024, 15:13 )Like Ra Wrote: I understand the question as "How did you manage to get out?"
If that's the question, then the answer is as follows:
I don't get out. In fact, I'm still trapped and am using a voice command to type this, and this voice command system has extra AI technology that is pretty good at understanding you even with a tube in your mouth.
😂😂😂
Kidding, obviously.
This vacbed stays airtight. I bring a remote to the vacuum pump inside with me (and also have outlet timers that the vacuum pump is plugged into as a backup). When I want out, I first make sure the vacuum is off. This does nothing immediately, since it's airtight. I then begin breathing in through my mouth through the tube, and breathing out through my nose inside the vacbed. I breathe like this on repeat until I've placed enough air back into the bed to move my arms so that I can unseal the top end and get out.
RE: I recently got my first LATEX vacbed - Like Ra - 15 Jan 2024
(15 Jan 2024, 16:32 )Peeklemeekle Wrote: I then begin breathing in through my mouth through the tubeAha, this is what the tube is for! It's not visible, how do you breath?
RE: I recently got my first LATEX vacbed - Peeklemeekle - 15 Jan 2024
(15 Jan 2024, 17:00 )Like Ra Wrote:(15 Jan 2024, 16:32 )Peeklemeekle Wrote: I then begin breathing in through my mouth through the tubeAha, this is what the tube is for! It's not visible, how do you breath?
What? There's a breathing tube there. It's just small and black and blends in with the bed if you don't look closely
RE: I recently got my first LATEX vacbed - Like Ra - 15 Jan 2024
Ah, just reread what you wrote - I understand now.... I thought, that tube is internal one to breathe out inside the latex.
RE: I recently got my first LATEX vacbed - Tinker D - 16 Jan 2024
Looks great, but I would need a partner or someone to watch over me, just in case.
RE: I recently got my first LATEX vacbed - Anne - 16 Jan 2024
I remember going from homemade plastic builds to finally a real latex one. Enjoy! But it looks like you're doing that 😁